Verilink 2048 (34-00179) Product Manual Instrukcja Użytkownika Pobierz pdf (Strona 31)

Terminal Operation 4-112048 PMU/NTU

4.7.1 General Functions

Set Time: The current time may be entered in this field

using the 24-hour HH:MM:SS format. For example, 3:45

AM is entered as ‘0345’ and 3:45 PM is entered as ‘1545’.

Set Date: The current date may be entered in this field

using the MM:DD:YY format. For example, July 4, 1994 is

entered as ‘070494’.

NOTE: The time and date can be set at the far end, but

not displayed.

New Password: This field allows entry of a password of up

to 10 characters. An empty string (carriage return only) may

be entered to disable the password feature. After <return> is

pressed, the new password is activated and is no longer visi-

ble. Therefore, type carefully when entering a new password

and verify before pressing <return>. When the Terminal

Interface is exited and later reactivated, this password must

be entered exactly to gain access. If the wrong password is

entered, the following message appears:

Incorrect Password; Please Enter Again

NOTE: Do not exit the Terminal Interface program

until the password procedure is fully understood. If a

password has been specified, it must be typed exactly to

reenter the program.

Maintenance Reset: This field will clear all user selectable

parameters, performance registers, passwords, and alarms.

All alarm threshold parameters will be reset to default val-

ues. The unit reloads start-up configuration settings from

the source specified by configuration switch S4 (refer to the

‘Installation’ chapter). Pressing <return> on this field brings

up the following warning:

DELETE ALL DATA AND RESTART UNIT?

(NO!) (YES)

To exit this screen without performing the reset function,

press <return> on (NO). To proceed with the reset function,

move the cursor to (YES) and press <return>. A mainte-

nance reset may also be performed using Switch S6-2 (refer

to Section 2.5.7 on page 2-4).

4.7.2 COA Parameters

The following fields pertain to the call on alarm (COA)

parameters.

Alarm Notification: This field controls remote alarm

reporting. The choices are:

[OFF] - Disables alarm reporting.

[DIRECT] - Sends reports to a printer or terminal con-

nected directly to the supervisory port.

[DIAL] - Sends reports through an attached ‘AT’ com-

mand set compatible modem connected to the ‘SUPV’

serial port, which must dial out to a remote modem. The

message format is described in the ‘Element ID’ field.

[DIAL NMS] - Sends reports through a modem to an

EM8000 network manager workstation.

Primary Phone#, Secondary Phone#: These fields are

ASCII strings for the primary and secondary call on alarm

(COA) phone numbers used in the [DIAL] and [DIAL NMS]

modes. The strings must be compatible with the standard

2048 PMU x.xx/x.xx 2048 PMU Date MM/DD/YY

2048 PMU x.xx/x.xx (Unit Address: xxx) Time HH:MM:SS

---------------------------------- UTILITIES -----------------------------------

Element: [NEAR]

Set Time: (14:10:13)

Set Date: (05/12/93)

Alarm Notification: [DIAL ]

Primary Phone#: (1 (205) 555-1212 )

Secondary Phone#: (9,,532-8853,,253 )

Element ID: (Example PMU 2048 )

New Password: ( )

(MAINTENANCE RESET)

Screen 4-8 Utilities

1 2 ... 26 27 28 29 30 31 32 33

Komentarze do niniejszej Instrukcji

Brak uwag

Verilink 2048 (34-00179) Product Manual Instrukcja Użytkownika Strona 31

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Sprzęt komputerowy Verilink 2048 (34-00179) Product Manual