Verilink SCM (880-503300-001) Product Manual Instrukcja Użytkownika Pobierz pdf (Strona 72)

Downloading and Broadcasting Firmware

6-8 Verilink SCM

Figure 6-4 Administration Menu

Select

W) write file to flash

to save the new file and select Yes to

write to flashbank B. This process takes about five minutes. As the

process completes, a message appears:

dnld_ramdisk: done

After another minute, the

Administration Menu

reappears. Select

Y) switch over once

to try your new code. When asked which bank

to boot from, choose “B”.

Copying Bank B to

Bank A

Verilink suggests that you DO NOT use the

Flash Copy

command

unless specifically instructed to do so by a Tech Support

representative or an upgrade procedure included with new

firmware files. No harm is done if bank A and bank B contain

different versions of firmware. A failed attempt to copy bank B to

bank A could leave an SCM module unable to boot.

By keeping the original version of firmware intact in bank A, you

can easily recover if an upgraded firmware version is later found to

have a problem.

SCM CONTROLLER ADMINISTRATION MENU --

SCM CONTROLLER ADMINISTRATION MENU --SCM CONTROLLER ADMINISTRATION MENU --

SCM CONTROLLER ADMINISTRATION MENU --

Date/Time/Zone: 8-26-98 21:25:20 PST

Date/Time/Zone: 8-26-98 21:25:20 PSTDate/Time/Zone: 8-26-98 21:25:20 PST

Date/Time/Zone: 8-26-98 21:25:20 PST

Node address: [0.0.0.2]

Node address: [0.0.0.2]Node address: [0.0.0.2]

Node address: [0.0.0.2]

Node id: 122

Node id: 122Node id: 122

Node id: 122

Site name: SCM Tutorial

Site name: SCM TutorialSite name: SCM Tutorial

Site name: SCM Tutorial

System uptime: 18:10:19

System uptime: 18:10:19System uptime: 18:10:19

System uptime: 18:10:19

--- NODE ADMINISTRATION ---

--- NODE ADMINISTRATION --- --- NODE ADMINISTRATION ---

--- NODE ADMINISTRATION ---

H) set shelf type Z) set time zone

H) set shelf type Z) set time zoneH) set shelf type Z) set time zone

H) set shelf type Z) set time zone

T) set time D) set date

T) set time D) set dateT) set time D) set date

T) set time D) set date

B) download firmware Y) switch over once

B) download firmware Y) switch over onceB) download firmware Y) switch over once

B) download firmware Y) switch over once

W) write file to flash O) switch over permanent

W) write file to flash O) switch over permanentW) write file to flash O) switch over permanent

W) write file to flash O) switch over permanent

C) set front/rear access Q) query firmware

C) set front/rear access Q) query firmwareC) set front/rear access Q) query firmware

C) set front/rear access Q) query firmware

A) set node address R) reset card

A) set node address R) reset cardA) set node address R) reset card

A) set node address R) reset card

I) change site name E) change node id

I) change site name E) change node idI) change site name E) change node id

I) change site name E) change node id

N) TCP/IP parameters P) change password

N) TCP/IP parameters P) change passwordN) TCP/IP parameters P) change password

N) TCP/IP parameters P) change password

M) modem parameters S) node selection

M) modem parameters S) node selectionM) modem parameters S) node selection

M) modem parameters S) node selection

X) exit this menu F) partition copy (B => A)

X) exit this menu F) partition copy (B => A)X) exit this menu F) partition copy (B => A)

X) exit this menu F) partition copy (B => A)

K) show shelf sync_master

K) show shelf sync_masterK) show shelf sync_master

K) show shelf sync_master

A [0.0.0.2] [1,1] SCM >

A [0.0.0.2] [1,1] SCM > A [0.0.0.2] [1,1] SCM >

A [0.0.0.2] [1,1] SCM >

1 2 ... 67 68 69 70 71 72 73 74 75 76 77 ... 82 83

Komentarze do niniejszej Instrukcji

Brak uwag

Verilink SCM (880-503300-001) Product Manual Instrukcja Użytkownika Strona 72

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Sprzęt komputerowy Verilink SCM (880-503300-001) Product Manual