Verilink WANsuite 6x30 (34-00315.B) Product Manual Instrukcja Użytkownika Strona 34
- Strona / 181
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
3-6
WANsuite 6x30
Framing
Selects the framing for the Network side of the DSU/CSU.
Values
ESF, D4
Default:
ESF
Coding
Sets the Network side line coding.
Values:
AMI, B8ZS
Default:
B8ZS
Line Build-Out
Sets the transmit Line Build Out (LBO) for the Network interface.
Values:
0,
−
7.5,
−
15.0,
−
22.5 dB
Default:
0 dB
Timing
Sets the timing source to synchronize the unit’s internal timing generators. In
all cases, slips are controlled to occur on frame boundaries at the Network
port when timing synchronization is lost.
Definitions of the timing sources are as follows:
Internal
– The unit’s internal frequency standard (T1 1.544 Mbps ± 50 bps)
is used for all timing.
Network
– Timing is derived from the Network port recovered clock.
Zero Suppression
Determines whether ones density insertion is activated after 15 zeros. This
parameter is ignored if the Coding parameter is set to “B8ZS.”
Values:
Disable, Enable
Default:
Disable
PRM Enable
Lets you establish which performance messaging standard will be employed
to initiate Performance Report Message (PRM) functions. Setting this field to
“Enable” instructs the unit to use ANSI T1.403, which sends a PRM once
every second. Setting this field to “Disable” instructs the unit to use AT&T
TR54016, which provides performance reporting on request only.
Values:
Disable, Enable
Default:
Disable
Error Status and Alarm Thresholds Table
The unit can be programmed to generate an alarm condition based on a
specific level of performance degradation. The Network screen presents a
table that provides current error status and alarm threshold information.
Acceptable alarm thresholds are set for periods of 15 minutes (900 seconds)
and sampled every second. The error types listed in the paragraphs below can
be preset to a value between 0 and 900 seconds. Setting a field to “0” (zero)
disables the alarm on that statistic. To effectively disable alarm reporting, set
all fields to “0” (zero).
The 15-minute time frame is not based on the TR 54016 or T1.403 interval
boundaries, but is a time window based on the accumulated counts over the
previous fifteen 1-minute intervals. In all cases, if the number of actual
- WANsuite 1
- Reference Manual 1
- Copyright Notice 2
- Documentation 2
- Disclaimer 2
- Warranty 2
- Table of Contents 7
- Chapter 3 8
- Chapter 4 9
- VT100 Interface 9
- Appendix A 10
- Specifications 10
- Appendix B 11
- SNMP Agent 11
- WANsuite 6x30 12
- About this Manual 13
- Telephone 14
- Internet 15
- Introduction 17
- Features of the WANsuite 18
- 6x30 Product Family 18
- SNMP Management 19
- Features Summary 20
- Front Panel 20
- WANsuite 6130 Rear Panel 21
- Indicator 21
- Description 21
- Ethernet LED Indicators 23
- Power Failure 24
- NSTALLATION 25
- Installation Wizard 26
- Installation 27
- Web Server Interface 29
- Layout of Interface Screens 30
- Figure 3.1 31
- Network Screens 33
- Figure 3.5 37
- Figure 3.6 37
- WANsuite 6230 Network Screen 38
- WANsuite 6430 Network Screen 39
- Network Services 41
- Service Details Button 41
- Interface Details Button 41
- Type Details Button 41
- Figure 3.11 42
- Figure 3.17 48
- Supervisory Screen 54
- Service Details Screen 55
- Delete Service Button 56
- ATM Virtual Channels Screen 60
- Figure 3.30 62
- Figure 3.31 62
- Figure 3.35 66
- Circuits Screen 72
- Static Routes Screen 75
- Route Details Screen 76
- Figure 3.55 86
- Figure 3.56 87
- Figure 3.57 87
- Figure 3.60 89
- Software Upgrade 94
- Figure 3.67 95
- Password 96
- Log Out Screen 97
- Cursor Controls 100
- NOTICE: 100
- Field Types 100
- Menu Structure 101
- CAUTION: 101
- System Screen 102
- Maintenance Reset 103
- Save and Restart 103
- Config Screens 104
- VT100 Interface 4-7 105
- Performance Screens 107
- Performance 30 Day Screen 108
- Figure 4.9 109
- Configuration Profiles 110
- Figure 4.10 111
- Alarm Profiles Screen 112
- Alarm Profile Details Screen 114
- Span Endpoints Screen 115
- Span Endpoint Details Screen 116
- Figure 4.16 117
- Figure 4.17 118
- 15-Minute and 1-Day Intervals 119
- Serial Screen 119
- VT100 Interface 4-23 121
- Ethernet (IP Details) Screen 122
- Service Details Screen 124
- IP Service Details Screen 125
- ATM Service Details Screen 125
- ATM Statistics Screen 126
- Figure 4.25 127
- Adding a New Virtual Channel 128
- Figure 4.26 129
- Figure 4.27 129
- HDLC/PPP Service 130
- Service Aware 131
- Rule Config Screen 131
- Figure 4.31 133
- SNMP Details Screen 134
- Diagnostics Screen 134
- Trap Log Screen 135
- Top Talkers Screen 136
- IP Gateway Screen 137
- RIP Parameters 138
- OSPF Parameters 138
- Circuit Table Screen 139
- Circuit Details Screen 139
- Static Route Table Screen 141
- Routes Details Screen 142
- Dynamic Route Table Screen 143
- Static ARP Table Screen 144
- ARP Details Screen 145
- Trusted Neighbors Screen 146
- Area Table Screen 147
- Area Details Screen 147
- Virtual Link Table Screen 149
- Virtual Link Details Screen 150
- NAT Details Screen 151
- 4-54 WANsuite 6x30 152
- Figure 4.51 153
- NAT Ports Screen 154
- NAT Port Details Screen 155
- NAT Port Status Table Screen 155
- Figure 4.56 156
- DHCP Details Screen 157
- Figure 4.58 158
- DHCP Hosts Screen 159
- Static Entries Screen 159
- IP Address List Screen 160
- IP Address Status Screen 161
- 4-64 WANsuite 6x30 162
- PECIFICATIONS 163
- Facility Data Link (FDL) 164
- 10/100 Ethernet 164
- Supervisory Port 164
- Industry Listings 165
- WANsuite 6230 Specifications 166
- Mechanical 167
- Environmental 167
- Standards 168
- WANsuite 6430 Specifications 169
- Standard Equipment 172
- Optional Equipment 172
- (Packet Use Only) 173
- 10/100 ETHERNET 174
- NETWORK 175
- SUPERVISORY PORT 175
- SNMP Configuration Parameters 177
- SNMP MIBs 177
- SNMP Trap Configuration 178
Powiązane produkty i podręczniki dla Sprzęt komputerowy Verilink WANsuite 6x30 (34-00315.B) Product Manual
Sprzęt komputerowy Verilink WANsuite 6450 (34-00326) Product Manual Instrukcja Użytkownika
(205 strony)
(205 strony)
Sprzęt komputerowy Verilink 1041 (CG) Configuration/Installation Guide Instrukcja Użytkownika
(2 strony)
(2 strony)
Sprzęt komputerowy Verilink 1042 (CG) Configuration/Installation Guide Instrukcja Użytkownika
(2 strony)
(2 strony)
Sprzęt komputerowy Verilink 1050 (CG) Configuration/Installation Guide Instrukcja Użytkownika
(2 strony)
(2 strony)
Sprzęt komputerowy Verilink WANsuite 7205 (34-00317.B) Product Manual Instrukcja Użytkownika
(221 strony)
(221 strony)
Sprzęt komputerowy Verilink 1251 (CG) Configuration/Installation Guide Instrukcja Użytkownika
(2 strony)
(2 strony)
Sprzęt komputerowy Verilink 1250 (CG) Configuration/Installation Guide Instrukcja Użytkownika
(2 strony)
(2 strony)
Sprzęt komputerowy Verilink 1544 (CG) Configuration/Installation Guide Instrukcja Użytkownika
(2 strony)
(2 strony)
Sprzęt komputerowy Verilink 1544E (CG) Configuration/Installation Guide Instrukcja Użytkownika
(2 strony)
(2 strony)
Sprzęt komputerowy Verilink 1544N (CG) Configuration/Installation Guide Instrukcja Użytkownika
(2 strony)
(2 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji